1. Sintering behaviour of natural porous hydroxyapatite derived from bovine
bone
2.
Sintering properties of hydroxyapatite powders
prepared using different methods
3.
Effects of silicate and carbonate substitution on
the properties of hydroxyapatite prepared by aqueous co-precipitation method
4.
Effects of silicate and carbonate substitution on
the properties of hydroxyapatite prepared by aqueous co-precipitation method
5.
Characteristics and properties of hydoxyapatite
derived by sol–gel and wet chemical precipitation methods
6.
Sintering and mechanical properties of MgO-doped
nanocrystalline hydroxyapatite
7.
Sintering behavior of hydroxyapatite prepared from
different routes
8.
Effect of zinc ions on the structural
characteristics of hydroxyapatite bioceramics
9.
Root cause failure analysis of a division wall
superheater tube of a coal-fired power station
10. Nanocrystalline forsterite for biomedical applications: synthesis,
microstructure and mechanical properties
11. Failure analysis on a primary superheater tube of a power plant
12. Failure investigation on rear water wall tube of boiler
13. Failure case studies of SA213-T22 steel tubes of boiler through computer
simulations
14. Failure investigation on deformed superheater tubes
15. The use of initial imperfection approach in design process and
buckling failure evaluation of axially compressed composite cylindrical shells
16. Thermal fatigue and corrosion fatigue in heat recovery area wall side
tubes
17. Effects of sintering additives on the densification and properties of
alumina-toughened zirconia ceramic composites
18. Effects of sintering additives on the densification and properties of
aluminatoughened zirconia ceramic composites
19. Properties of hydroxyapatite synthesize by wet chemical method
20. Exact solution for stresses/displacements in a multilayered hollow
cylinder under thermo-mechanical loading
21. Oxide scale growth and presumed exfoliation in a 700 C or higher steam
condition: A simulation study for future operations of ultra-supercritical
power plants
22. Deep drawing characteristics of square cups through conical dies
23. Development of a bone substitute material based on alpha-tricalcium
phosphate scaffold coated with carbonate apatite/poly-epsilon-caprolactone
24. Fatigue growth analysis of a surface crack in a solid cylinder under
combined cyclic axial-torsion loading
25. Empirical solutions for stress intensity factors of a surface crack in a
solid cylinder under pure torsion
26. Stress intensity factors of a corner crack emanating from a pinhole of a
solid cylinder
27. Analysis of surface cracks in round bars using dual boundary element
method
28. Prediction of oxide scale growth in superheater and reheater tubes
29. Fatigue crack growth of a corner crack in a square prismatic bar under
combined cyclic torsion–tension loading
30. Effect of copper oxide and manganese oxide on properties and low
temperature degradation of sintered Y-TZP ceramic
31. Hydrogen damage in a rear riser water wall tube of a power plant
32. Determination of correlation functions of the oxide scale growth and the
temperature increase
33. Increase in ironing limit of aluminium alloy cups with lubricants
containing nanoparticles
34. Characterization of forsterite ceramics
35. Surface crack growth in a solid cylinder under combined cyclic
bending-torsion loading
36. Evaluation on reheater tube failure
37. High operating steam pressure and localized overheating of a primary
superheater tube
38. Influence of manganese on the sintering properties of tetragonal
zirconia
39. Effects of carburization on expected fatigue life of alloys steel shafts
40. Pitting corrosion of triggering initial fractures of palm oil screw
press machine shafts
41. Effect of sintering holding time on low-temperature degradation of
yttria stabilised zirconia ceramics
42. Simulating the implications of oxide scale formations in austenitic
steels of ultra-supercritical fossil power plants
43. Mechanochemical synthesis of nanohydroxyapatite bioceramics
44. Fatigue growth of a surface crack in a V-shaped notched round bar under
cyclic tension
45. Failure analysis on high temperature superheater Inconel® 800 tube
46. A new method for estimating heat flux in superheater and reheater tubes
47. A fuzzy model for evaluation and prediction of slurry erosion of 5127
steels
48. Synthesis and properties of biphasic calcium phosphate prepared by
different methods
49. Fatigue Evaluation of Pressure Vessel using Finite Element Analysis
based on ASME BPVC Sec. VIII Division 2
50. Sintering Behavior of Nanocrystalline Hydroxyapatite Produced by Wet
Chemical Method
51. Buckling analysis of shear deformable plates by boundary element method
52. Effect of sintering holding time on the properties and low-temperature
degradation behaviour of manganese oxide-doped Y-TZP ceramic
53. Estimation of oxide scale growth and temperature increase of high
(9–12%) chromium martensitic steels of superheater tubes
54. Sintering and properties of magnesium orthosilicate ceramic
55. Fracture analysis of a corner crack in a pinhole of a solid cylinder
under torsion loading.
56. Zinc-substituted hydroxyapatite produced from calcium precursor derived
from eggshells
57. Large deformation of shear-deformable plates by the boundary-element
method
58. Low-temperature degradation (LTD) behaviour of CuO-Doped tetragonal
zirconia ceramic
59. Failure investigation on reheater tube due to deposit and wall thinning
60. Stability of Euler's method for evaluating large deformation of shear
deformable plates by dual reciprocity boundary element method
61. Effect of annealing treatment on the characteristics of bovine bone
62. Notch root strain measurement of WE43-T6 magnesium alloy using
electronic speckle pattern interferometry
63. Mechanism analysis of a main landing gear of transporting aircraft: A
design learning perspective
64. Iterative technique and finite element simulation for supplemental
condition monitoring of water-tube boiler
65. Effect of calcination on the sintering behaviour of hydroxyapatite
66. Low-temperature degradation and defect relationship in yttria-tetragonal
zirconia polycrystal ceramic
67. Failure investigation on reheater pendent tubes due to external scale
exfoliation and internal scale formation
68. Mechanical Properties of Concrete Block Reinforced with Recycle HDPE and
Coal Bottom Ash
69. Analytical Solution of Thermo-Mechanical Stresses of Multi-Layered
Hollow Spherical Pressure Vessel
70. Numerical Fracture Mechanics as A Practical Failure Investigatorvy Tool:
The Outlook of Cracked Round Bars
71. Evaluation on the hardness and microstructures of T91 reheater tubes
after post-weld heat treatment
72. Hydrogen embrittlement due to mild condensate contamination by sea water
ingress through condenser tube leakages: A case study
73. Forming box-shaped ends in circular tubes
74. Effects of two-step sintering on the properties of hydroxyapatite
bioceramic
75. An incident investigation on stub tube at high temperature reheater
outlet header region of a power plant
76. Densification behavior of Y-TZP containing zirconium diboride composites
77. Effect of forsterite addition on the densification and properties of
hydroxyapatite bioceramic
78. Influence of magnesium doping in hydroxyapatite bioceramics sintered by
short holding time
79. Analysis on a failed 2.25 Cr–1Mo reheater bent tube at upper bank
vertical tubes region
80. Assessment of a planar inclusion in a solid cylinder
81. Evaluation on an internal surface crack in a compound tube
82. Effect of ultrasonication on synthesis of forsterite ceramics
83. Analyzing size effects in a cracked orthotropic layer under antiplane
shear loading
